well, I happen to LIKE women....especially my lovely wife...sorry that it didn't work out for you,...and I am not a dog person, I am a cat person...Your much better off with a dog. LOL
well, I happen to LIKE women....especially my lovely wife...sorry that it didn't work out for you,...and I am not a dog person, I am a cat person...Your much better off with a dog. LOL
A cat would be great too, and you don't have to walk them.well, I happen to LIKE women....especially my lovely wife...sorry that it didn't work out for you,...and I am not a dog person, I am a cat person...
I always get lucky!!!A cat would be great too, and you don't have to walk them.
What's with all the brown nosing the wife, you hoping to get lucky tonight? LOL
I've never had a linear tracker but always wanted to. I'm a big fan of women and have had the same one for 30 years now.
New Orleans.I think I would just get a refund. It is possible to get anything fixed but the question is , is it worthwhile.
I went back and looked at the auction and the seller touted it as working and original and like new. Where are you located?
I notified the seller ...and I SHOULD know how to notify ebay but I don't...Is there an audio repair shop in New Orleans?
What cyber1 says makes plenty of sense. I am not familiar with this particular linear tracker.
It did indeed look very low mileage but that doesn't tell you if a weak spot in the design has failed.
Sometimes gear gets stiff sitting in storage. Try exercising it for a while. You might be pleasantly surprised.
You should notify both the seller and ebay immediately. Be aware of what ebays time limits are to open a case or ask them for a refund. Ebay will DEFINITELY give refunds even if the seller says no.
Especially if they advertised the unit as working and it doesn't. It boils down to whether you want to grab the ball for restoration. I wouldn't attack it with a screwdriver nor pay anyone to do so, until and unless somebody puts in writing that they will guarantee your refund. Sometimes repair attempts can make matters worse. It might be that the best course of action is just return it. Depends how badly you want it.
I think I would just get a refund. It is possible to get anything fixed but the question is , is it worthwhile.
I went back and looked at the auction and the seller touted it as working and original and like new. Where are you located?
Is it this one?I had the same problem with a PX3 I purchased on eBay. The seller didn’t have the plastic piece that locked down the sled that the arm rides on so it wouldn’t move during transit. This resulted in the sled breaking the arm off one of the two micro switches that control the start of the platter during operation. When you press play, the sled starts to move towards the center. After a short distance it pushes down the first lever which starts the platter. After the arm lowers and the record plays and the arm lifts, the sled hits the second lever which stops the platter and the sled returns to the start position. If the second lever or switch is damaged, the platter will not stop and you have the problem you’ve described.
I downloaded the PX 3 service manual from the web https://www.vintageshifi.com/repertoire-pdf/pdf/telecharge.php?pdf=Yamaha-PX-3-Service-Manual.pdf and disassembled my PX 3. The micro switch is part #18 on the diagram of the Tonearm Unit. I was unable to find a replacement micro switch that had the lever attached but did find a nearly identical micro switch at Dig-Key that had a flat top ( Digi-Key part # D2SW-P2L1D-ND ) that I could super glue the original lever to. I did so and installed the modified micro switch. It worked perfectly And still does ( 5 years later ).
Holy Moley!That’s the one. You will have to remove the assembly it’s attached to and then unsolder it’s six feet from the circuit board ( a desoldering iron works best as there is less chance of overheating the solder traces on the board and damaging them but desoldering braid will work if you’re careful to not overheat ). You then solder the new micro switch back in ( making sure you’ve oriented it correctly with the hinge side on the same side as the original. Then superglue the lever from the original micro switch to the new switch also making sure that the white plastic trip lever on the lever is the same distance from the hinge as the non damaged one and also being careful not to get any of the super glue anywhere else but on the joint between the broken lever and the metal lever on the replaced micro switch Here are photos of my undamaged micro switch and the damaged switch I originally tried to repair by gluing the broken lever back onto the original switch ( it wouldn’t hold ).
View attachment 47422View attachment 47423View attachment 47422View attachment 47423
Enter your email address to join: